Page 1 of 66 | Next >

Subcategories
Caliper
Gages
Indicator
Level
Micrometer
Precision Tools Accessories
Shim


Manufacturers
Precision Brand
Starrett

Product Categories
Abrasives & Cutting Tools
Chemical Lubricants Sealants & Paint
Electrical & Lighting
Hand Tool
Machinery & Equipment
Material Handling
MRO & Contractor Supplies
Power & Hydraulic Tools
Precision Tools
Safety & Security
Welding






Wiggler/Center Finder No. S828

Wiggler/Center Finder No. S828 and four different attachments adapt to countless applications and are readily interchangeable. The attachments are snapped in the chuck without removing the collet nut and are clamped by a ball swivel-joint which permits adjustment to an angular position or true concentricity.....(more info)


Wiggler/Center Finder No. S828

SKU: STRS828HZ


V-Blocks and Clamps for round or square work

These rugged and versatile blocks have the following features: Hardened steel, precision ground parallel and square V-grooves are ground central and parallel to the sides and base – perfect alignment in matched pairs Clamps have screw holes at 45 degrees and 90 degrees to hold either square or round work Stepped groove construction permits hi....(more info)


V-Blocks and Clamps for round or square work

SKU: STR568C


V-Blocks and Clamps

Starrett No. 278 V-Blocks are precision ground to extreme accuracy. The vees are central, parallel, and square with the ends and sides. The blocks are made of steel, hardened and ground and numbered in series so that the vees in each set are always in alignment. The blocks have a 1/4-20 tapped hole through the sides so that they may be attached to ....(more info)


V-Blocks and Clamps

SKU: STR278


V-Block and Clamp

This is an improved V-block and clamp which has these very versatile features: Can be used on its base, on the end or on either side The clamp is smaller than the outside width of the block, but has an adjustable side screw to support the block and prevent tilting The V at the stepped end is at right angles to the base and is handy for holding s....(more info)


V-Block and Clamp

SKU: STR567


Upright Base Post

3/8"􏰀(9.5mm) diameter x 7-7/16" (190mm) length overall. Starrett No. 57S and No. 58S Universal Snugs may also be used.....(more info)


Upright Base Post

SKU: STR657G


Universal Snugs for surface gages

These universal snugs (sometimes called sleeves) provide a convenient means of attaching scribers and test indicator shanks to surface gages, Starrett No. 657 Series Magnetic Bases, indicator tool post holders and gage rods. These snugs will fit all Starrett No. 57 and No. 257 Surface Gages and all test indicator clamps and tool post holders. No. 5....(more info)


Universal Snugs for surface gages

SKU: STR58S


Universal Snugs for surface gages

These universal snugs (sometimes called sleeves) provide a convenient means of attaching scribers and test indicator shanks to surface gages, Starrett No. 657 Series Magnetic Bases, indicator tool post holders and gage rods. These snugs will fit all Starrett No. 57 and No. 257 Surface Gages and all test indicator clamps and tool post holders. No. 5....(more info)


Universal Snugs for surface gages

SKU: STR57S


Universal Back-Plunger Dial Indicators

Our No. 196 Indicator is one of the most versatile indicators available ... and it is the “granddaddy” of them all. Over the years this tool has been improved by methods and materials but the basic design is unchanged. The design is older than most of you and has withstood the test of time and beaten all challengers because it is: Accurate and....(more info)


Universal Back-Plunger Dial Indicators

SKU: STR196MB5

Page 1 of 66 | Next >